E3100 Jumper and Switch Settings
HELP: Board Views, Hardware Tables.
There are no jumper or switch settings for the E3100 series DNI Cards. All configuration settings are software selectable via the IBM Reference Disk.
Typical IBM Reference Disk Screens with Ethernet, Token Ring, and FDDI DNI Card examples.
Main Menu
Select One:
1. Start operating system
2. Backup/Restore system programs.
3. Set configuration
4. Set features
5. Copy an option diskette
6. Test the computer
7. Display revision levels
Enter F1=Help F3=Exit
Set Configuration
1. View configuration.
2. Change configuration.
3. Backup configuration.
4. Restore configuration.
5. Run automatic configuration.
6. Set and view SCSI device configuration.]
7. Display memory map.
Enter F1=Help F3=Exit
Change Configuration
Total System Memory
Installed Memory .......................................... 16384KB (16.0MB)
Usable Memory ............................................ 16000KB (1l5.6MB)
Built In Features
Installed Memory .......................................... 16384KB (16.0MB)
Diskette Drive 0 Type ................................... [l1.44MB k3.5" ]
Diskette Drive 1 Type .................................... [1.2MB 5.25" ]
Diskette Drive 2 Type .................................... Not installed
Math Coprocessor ........................................ Not installed
Serial Port ................................................... [SERIAL 1 ]
Serial Transmit Arbitration Level .................... [Shared 7 ]
Serial Receive Arbitration Level ...................... [Shared 7 ]
Parallel Port ................................................. [PARALLEL 1]
Parallel Port Arbitration Level ......................... [Shared 7 ]
Preempt Enable/Disable ................................ [Enable ]
(use F8=Fwd)
Slot 1 - IBM PS/2 SCSI Adapter w/Cache
I/O Address .................................................. [3540-3547]
DMA Arbitration Level .................................... [Level C]
Fairness On/Off ............................................ [On ]
ROM Wait State Disable ............................... [Enable Wait State]
SCSI Adapter Address (ID) ............................ [7]
Slot 2 - Cabletron Systems Inc. F3069 FDDI Adapter
Chip Select for I/O Address ........................... [Base Address: 0300]
Boot ROM Base Address .............................. [Boot ROM not installed]
Streaming Data ............................................ [Enabled]
24 or 32 Bit Addressing ................................ [32 Bit Address]
Interrupt Level .............................................. [Level 5]
Arbitration Level ........................................... [Arbitration Level 8]
Bus Master Fairness .................................... [Enabled]
Slot 3 - Cabletron Systems Inc. E3100 Series Ethernet Adapter w/ 16
Adapter E3100 I/O Base Address .................. [Base Address: 001300]
E3100 Shared RAM Base Address ................ [Base Address: 0C0000]
E3100 Boot ROM Base Address ................... [Boot Prom not installed]
Output Port Select ....................................... [Primary]
Adapter Interrupt Level .................................. [Interrupt 10]
Slot 4 - Empty
Slot 5 - XGA Video Adapter
Video I/O Address ....................................... [Intance 2: 2120h - 212Fh]
Video Arbitration Level ................................. [Arbitration level 13]
Video Fairness ............................................ [Fairness On]
Slot 6 - Empty
Slot 7 - Empty
Slot 8 - IBM Token-Ring Network 16/4 Adapter/A
Primary or Alternate adapter .......................... [Primary]
Adapter Data Rate ........................................ [16 Mbps]
ROM Address Range .................................... [CC000-CDFFF]
RAM Size and Address Range ...................... [16 KB / D80000-DBFFF]
Interrupt Level .............................................. [Interrrupt 2]
F1=Help F3=Exit F5=Previous F6=Next F7=Bkwd